WL-9001CS
You are here: Home » Product Center » Ethylene » WL-9001CS » WL-9001CS

Related Products

loading

Share to:
sharethis sharing button

WL-9001CS

Availability:
Quantity:
  • WL-9001CS

  • WangLin NM

Product Description

WL-9001CS is a high-performance bisphenol A-type vinyl resin. At the same time, the resin has the advantages of high strength, good heat resistance, and wide applicability. It can withstand most acids, alkalis, salt solutions and some solvents below 90°C. of erosion.


Application

WL-9001CS resin is suitable for hand lay-up, pultrusion, winding and other FRP forming processes, to produce corrosion-resistant integral FRP products of various specifications, and to produce corrosion-resistant FRP protective layers on the surfaces of metal structures and concrete structures.

 

 Properties

performance

Parameter

unit

standard test

Exterior

light color transparent

-

GB/T8237

Viscosity 25℃

300-500

mPa.s

GB/T7193

Acid value

6-14

mgKOH/g

GB/T2895

solid content

54-60

%

GB/T7193

25℃ gel time

25-35

minutes

GB/T7193

Note: 25℃ gel time: add 1.0g 1% cobalt and 1.5g M50 (AKZO-Nobel) to 100g resin.


Liquid Resin Properties (Typical Values)

performance

numerical value

unit

standard test

Storage period (uninitiated, dark place), 20℃

3

month

-


Resin cast body properties (typical values)

performance

Parameter

unit

standard test

Tensile Strength

75

MPa

GB/T2567

Tensile elastic modulus

3400

MPa

GB/T2567

Elongation at break

3.5

%

GB/T2567

Bending strength

130

MPa

GB/T2567

bending elastic modulus

3100

MPa

GB/T2567

Impact strength

14

KJ/m2

GB/T2567

Heat distortion temperature

100

GB/T1634

Curing conditions: 24 hours at room temperature, 40°C, 60°C, and 80°C.

 2 hours, 1 hour after curing at 100℃

Test conditions: temperature 23±2 ℃, relative humidity 50±6%

 


Instructions and precautions for use

1.      Products cured at room temperature must also undergo post-curing treatment in order to achieve optimal physical and chemical properties.Before this, the products need to go through 24   Hours room temperature cure.Post-curing conditions are: 80-100℃×3~6   hours (longer for thick products).Post-cure is especially important for parts intended to be chemically resistant.

2.      Factors that affect the gel time during actual use include: ambient temperature, humidity, concentration of initiator and accelerator, fillers and additives. Therefore, it is recommended to conduct a small test according to different construction environments before use to adjust the concentration of initiators and accelerators. Suitable dosage.

3.      During construction, please add an appropriate amount of accelerator to the resin according to the formula determined in the pilot test and mix well, then add an appropriate amount of initiator and mix well. It is strictly forbidden to directly contact the initiator and accelerator and add them at the same time.

 

 


Storage conditions

1.   Before use, the resin should be stored in the original packaging (to avoid opening and damaging the barrel) in a dry room below 25°C.

2.   The increase in temperature and exposure to light will significantly shorten the storage period. Avoid direct sunlight and keep away from heat sources during storage.

3.   Unsaturated polyester resin liquid containing styrene is flammable and should be stored away from open flames.Please refer to the safety data sheet.

 

All various data are derived from our in-depth research and extensive practice and are therefore completely trustworthy.However, since the production of products is affected by multiple factors, we are not responsible for the actual performance, effects and effects caused by the above data and the specific application and processing of the products, as well as the resulting direct and indirect losses.Before selecting the above products, users are requested to check and confirm the relevant product quality, performance indicators, safety and other data themselves.At the same time, users should also pay attention to avoid infringing various relevant laws, registered trademarks and patent rights.We are not responsible for this.


Version number: 2021/1.0

Publication date: 2021/01

Shandong Wanglin New Material Co., Ltd.

Address: Chemical Industry Park, Pingyuan County Economic Development Zone, Dezhou City, Shandong Province

T:(86)15863477700 

E: scott.cui@wl-upr.com


Previous: 
Next: 
 
Hubei Wanglin New Material Technology Co., Ltd. is a new company specializing in the production of unsaturated polyester resins in Hongwanglin New Material Technology Co., Ltd., the company's registered capital of one hundred million yuan, main technological relying on Shandong Wanglin New Material Technology Technology Ltd. and its subordinate production bases.

Quick Navigation

Product Category

Product Inquiry
All rights reserved2022 Hubei Wanglin New Material Technology Co., Ltd. 鄂ICP备2021007343号-1