WangLin NM
Product properties
WL-4001 is a pre-promoted general purpose unsaturated polyester resin. The resin has low viscosity and good glass fiber infiltration; Low shrinkage, high toughness, high strength and so on.
Main application
WL-4001 resin is mainly formed by vacuum introduction, which is widely used in automobile parts, cooling towers and other fields.
Product specification
performance | scope | unit | standard test |
Exterior | Red and transparent | - | GB/T8237-2005 |
Viscosity 25 ℃ | 140-200 | mpa.s | GB/T7193-2008 |
Acid value | 16-24 | mgkoh/g | GB/T2895-2008 |
Solid content | 57-63 | % | GB/T7193-2008 |
Gel time 25 ℃ | 10-30 | minutes | GB/T7193-2008 |
Note: 25 ℃ Gel Time: 100g resin plus 1.5g Wanglin curing agent.
Liquid resin performance (typical value)
performance | Value | unit | standard test |
Storage period (not caused, dark parts) | 3 | 月 | - |
Resin pouring performance (typical value)
performance | Value | unit | standard test |
Tensile Strength | 65 | MPA | GB/T2567-2008 |
Stretching elastic modulus | 3000 | MPA | GB/T2567-2008 |
Fracture extension | 4.5 | % | GB/T2567-2008 |
Bending strength | 110 | MPA | GB/T2567-2008 |
Bending elastic modulus | 3300 | MPA | GB/T2567-2008 |
Impact strength | 13 | Kj/m2 | GB/T2567-2008 |
Heat distortion temperature | 75 | ℃ | GB/T1634-2004 |
CIThization conditions: room temperature to curing for 24 hours, 40 ° C, 60 ° C, 80 ° C after curing
2 hours
Test conditions: temperature 23 ± 2 ℃, relative humidity 50 ± 6 %
Instructions and precautions
1.WL-4001 resin has accelerant, the curing agent can be MEKP, should ensure that the curing agent in the effective period. MEKP/Co curing systems are usually used at temperatures not lower than 15 ° C. When the temperature is low, accelerants can be added appropriately to adjust the reactivity.
2. When using, we must pay attention to control the water content of glass fiber, filler, pigment paste and other materials, and pay attention to the compatibility of pigment paste and unsaturated polyester resin.
Storage conditions
1. Before use, the resin should be stored in the original package (to avoid the damage of opening the drum and the drum) in a dry room below 25℃.
2. The increase of temperature and light exposure will significantly reduce the storage period, and the storage should be kept away from direct sunlight and heat source.
3. The unsaturated polyester resin liquid containing styrene is flammable, and should be stored away from an open flame.Please refer to the safety data sheet.
All kinds of data are derived from our in -depth research and extensive practice, so it is completely credible. However, due to the multiple factors of product production, we are not responsible for the actual performance, effects and impacts caused by the above data and the specific application and processing of the products and the processing of the product, and the direct and indirect losses caused by it. Before selecting the above products, please check the product quality, performance indicators, security and other data and confirm it by themselves. At the same time, users should also pay attention to avoid violations of various relevant bills, registered trademarks and patent rights. We are not responsible for this.
Version number: 2021/1.0
Publishing date: 2022/02
Hubei Wanglin New Material Technology Co., Ltd.
Address: south of Xinghua 3rd Road, Jingmen Chemical Circle Industry, Hubei Province
Tel: 0533-6236816
Fax: 0533-6236816
Product properties
WL-4001 is a pre-promoted general purpose unsaturated polyester resin. The resin has low viscosity and good glass fiber infiltration; Low shrinkage, high toughness, high strength and so on.
Main application
WL-4001 resin is mainly formed by vacuum introduction, which is widely used in automobile parts, cooling towers and other fields.
Product specification
performance | scope | unit | standard test |
Exterior | Red and transparent | - | GB/T8237-2005 |
Viscosity 25 ℃ | 140-200 | mpa.s | GB/T7193-2008 |
Acid value | 16-24 | mgkoh/g | GB/T2895-2008 |
Solid content | 57-63 | % | GB/T7193-2008 |
Gel time 25 ℃ | 10-30 | minutes | GB/T7193-2008 |
Note: 25 ℃ Gel Time: 100g resin plus 1.5g Wanglin curing agent.
Liquid resin performance (typical value)
performance | Value | unit | standard test |
Storage period (not caused, dark parts) | 3 | 月 | - |
Resin pouring performance (typical value)
performance | Value | unit | standard test |
Tensile Strength | 65 | MPA | GB/T2567-2008 |
Stretching elastic modulus | 3000 | MPA | GB/T2567-2008 |
Fracture extension | 4.5 | % | GB/T2567-2008 |
Bending strength | 110 | MPA | GB/T2567-2008 |
Bending elastic modulus | 3300 | MPA | GB/T2567-2008 |
Impact strength | 13 | Kj/m2 | GB/T2567-2008 |
Heat distortion temperature | 75 | ℃ | GB/T1634-2004 |
CIThization conditions: room temperature to curing for 24 hours, 40 ° C, 60 ° C, 80 ° C after curing
2 hours
Test conditions: temperature 23 ± 2 ℃, relative humidity 50 ± 6 %
Instructions and precautions
1.WL-4001 resin has accelerant, the curing agent can be MEKP, should ensure that the curing agent in the effective period. MEKP/Co curing systems are usually used at temperatures not lower than 15 ° C. When the temperature is low, accelerants can be added appropriately to adjust the reactivity.
2. When using, we must pay attention to control the water content of glass fiber, filler, pigment paste and other materials, and pay attention to the compatibility of pigment paste and unsaturated polyester resin.
Storage conditions
1. Before use, the resin should be stored in the original package (to avoid the damage of opening the drum and the drum) in a dry room below 25℃.
2. The increase of temperature and light exposure will significantly reduce the storage period, and the storage should be kept away from direct sunlight and heat source.
3. The unsaturated polyester resin liquid containing styrene is flammable, and should be stored away from an open flame.Please refer to the safety data sheet.
All kinds of data are derived from our in -depth research and extensive practice, so it is completely credible. However, due to the multiple factors of product production, we are not responsible for the actual performance, effects and impacts caused by the above data and the specific application and processing of the products and the processing of the product, and the direct and indirect losses caused by it. Before selecting the above products, please check the product quality, performance indicators, security and other data and confirm it by themselves. At the same time, users should also pay attention to avoid violations of various relevant bills, registered trademarks and patent rights. We are not responsible for this.
Version number: 2021/1.0
Publishing date: 2022/02
Hubei Wanglin New Material Technology Co., Ltd.
Address: south of Xinghua 3rd Road, Jingmen Chemical Circle Industry, Hubei Province
Tel: 0533-6236816
Fax: 0533-6236816